Vag com interface

pesimist · 14-12-2009 15:30:29

Koliko vidim okom izgorio mi je LM393 u interfaceu. Ima li netkoideju zbog èega, i da li æe ovo èudo raditi ako ga zamjenim. testirao sam ibizu 1.9sdi i radio je sve ok. Onda sam izašao iz engine ecu i mprobao tablu nema šanse i nakon toga više ništa. LM je eksplodirao jer mu fali komadiæ sa sredine tijela.

i da mjerio sam k- liniju sa unimerom i sve je ok, istina kada skopèam unimer dodje 12volt na k-liniji ali stavim li otpor izmeðu k-linije i mase voltaza padne ispod 1volt. neznam zašto se to desilo.

Zadnja izmjena od pesimist (14-12-2009 15:57:33)

koyot · 14-12-2009 15:52:34

isplativije ti je kupit ili napravit drugi nego taj popravljat

mlulic · 14-12-2009 16:49:23

ako radiš ovaj posao ozbiljno kupi orginal imaš u blizin i prestavništvo

pesimist · 14-12-2009 17:13:36

di to ima ?

plavac65 · 14-12-2009 19:18:00

Vidi gore u plavoj traci piše Web trgovina...pozzz

pesimist · 14-12-2009 19:56:23

ma znam tu plavu traku , a našao i ono šta mlulic reèe. sve u svemu proba æu zamjeniti lm393 i vidjeti ako radi dobro ako ne, djed mraz možda donese novi, ko zna možda!

koyot · 14-12-2009 20:00:36

daje samo lm lako bi bilo ima tu jos stosta za zamijenit

pesimist · 14-12-2009 20:04:17

pa mogao si napisati barem nešto od tih štošta, lakše bi se djed mraz odluèio.

autoservis-edo · 14-12-2009 20:33:41

o kojem je vag comu rijec...??

mlulic · 15-12-2009 01:09:57

Imaš email

pesimist napisao:

di to ima ?

pesimist · 15-12-2009 11:03:05

imam da. hvala

koyot · 17-12-2009 22:53:19

beli si rijesio dok se nejavljas a samo da znas da VAG COM 704,1 radi sa softwarom 20070422 ,a 805.1 sa soft 20080823 ,druge verzije softw, prouzrokuju sprogramiranje ,evo malo uputstvo prije upotrebe ,

Step1: Please ensure that you have installed the VAG-COM software.

Step2: Plug your disabled cable to the USB. There maybe be a pop-up window to indicate you to install the driver, for damaged cable, let it be, skip it.

Step3: Right click "my computer", select " hardware", then "device manager", then "Other device", the " USB device".

Step4: Right click "USB device", select "properties", select " detail", there will be a line information displayed. VID_xxxx & PID_xxxx, please write down the 4 letters or number for VID and PID.

Step5: Unplug the cable, select" my computer" --"C:/"--"Program files"--"VAG-COm"--"VAGUSB.inf".

Step6: In item [FtdiHw], please add one more line as " %USB\VID_xxxx&PID_xxxx.DeviceDesc%=FTD2XX, USB\VID_xxxx&PID_xxxx", please ensure the four number or alphabets are the same as the ones you write down in step 4.

Step7: In the end of the text, add one more line as " USB\VID_xxxx&PID_xxxx.DeviceDesc="VAG-COM Compatible USB Interface", the four numbers or alphabets are also the same as the ones you write down in step4.

Step8: Save "VAGUSB.inf" file and then exit.

Step9: Unplug the cable, and then plug the cable to the USB port. System will indication found new hardware, and will pop up window for driver update. If do not have the pop up window, let it be, Right click "my computer", select " hardware", then "device manager", then "Other device", then right click "USB device", select update drive.

Step10: Let the driver point to C:/program files/vagcom

Step11: System will search the drive for several seconds, then it will indicate that find the driver and then install it.

Step12: Open the software "vidpidfix.exe" i sent you. Click "search", there will be indication two lines of information. First " found one device", second "0".

Step13: Click "0", then click "open", the information will be displayed in he blank dialogue. Click "write default EE data", if success, there will be a pop up information " wirte successful". Then click "ok" and exit.

Step14: Unplug cable and then plug cable.

Step15: Just as the step 10, update the drive and let the file point to the file "VCR_CDM 2.00.00" that i send you. There will be a indictaion information that it install completrly.

step16: Open the file" Mprog2.8_setup.exe". Click" device" and then"scan", if above steps are all well done, there will be information " find one device".

Step17: Use Mprog2.8.exe to open file " genius vag com ept.ept" that i sent you. Then click "erase", if succeed, there will be a information " successful", and then click " program" , if succeed, there will be a informtion " programmed serial under disabled"

Step18: Your computer can recognize the cable now and your cable is ready to use.

na ovaj nacin samo kako se izrazit popravis ftdi ,a ako je sprogramiran chip atmega onda je procedura druga znaci reprogramiranje
pozdrav

elprog forum

#1 14-12-2009 15:30:29

Vag com interface

#2 14-12-2009 15:52:34

Re: Vag com interface

#3 14-12-2009 16:49:23

Re: Vag com interface

#4 14-12-2009 17:13:36

Re: Vag com interface

#5 14-12-2009 19:18:00

Re: Vag com interface

#6 14-12-2009 19:56:23

Re: Vag com interface

#7 14-12-2009 20:00:36

Re: Vag com interface

#8 14-12-2009 20:04:17

Re: Vag com interface

#9 14-12-2009 20:33:41

Re: Vag com interface

#10 15-12-2009 01:09:57

Re: Vag com interface

#11 15-12-2009 11:03:05

Re: Vag com interface

#12 17-12-2009 22:53:19

Re: Vag com interface

Board footer