Trenutno niste prijavljeni. Za prikaz svih foruma potrebna je registracija.
Stranice: 1
Vidi. Ja zapravo radim na ovom ljubiteljski. Ja isto takve stvari radim kao developer u telekomunikacijski svrhi programer (real time embedded system). I znam kako je to reverse inzeniring.
Mozda cu sam, da nastudiram ove uredjaje kao i ti. Ali za to ba¹ treba puno vremena.
Interfejs je K+CAN. A koji softwer ima¹?
Da ima¹ pravo. Znam, da je ovaj reverse in¾eniring veoma komplicirovan.
Kako ti zna¹ na kojima mjestima OFFSET treba korekcija.
Ali da se vrijeme skrati je mozda bolje da se uzme ne¹to ovakvo:
/
Hvala. Da ovo je opcija.
Ali je isto tako moguèe preko programatora. UPA USB mislim, da ne ide!
Sa kojim eprom programatorom se mo¾e ovaj èip da se bere i pi¹e?
Ovaj eprom je u BOSCH AIRBAG modulu.
Puno hvala.
Pa imam mnogo fajlova za AIRBAG reset. Ako nekomu nesto zatreba neka ka¾e, pa èu dati gore.
AIRBAG DUMPS:
naprimjer:
AUDI:
- 4A0 959 655 Bosch 0 285 001 036 93C46
- 4B0 959 655 C Bosch 0 285 001 106 HC11KA4
i tako dalje.
Ako mislite sa ovim tipom interfejs? Meni ne treba shema interfejsa. Ja molim za dokument standarde:
SAE standards documents on OBD-II
* J1962 - Defines the physical connector used for the OBD-II interface.
* J1850 - Defines a serial data protocol. There are 2 variants- 10.4 kbit/s (single wire, VPW) and 41.6 kbit/s (2 wire, PWM). Mainly used by US manufacturers, also known as PCI (Chrysler, 10.4K), Class 2 (GM, 10.4K), and SCP (Ford, 41.6K)
* J1978 - Defines minimal operating standards for OBD-II scan tools
* J1979 - Defines standards for diagnostic test modes
* J2012 - Defines standards trouble codes and definitions.
* J2178-1 - Defines standards for network message header formats and physical address assignments
* J2178-2 - Gives data parameter definitions
* J2178-3 - Defines standards for network message frame IDs for single byte headers
* J2178-4 - Defines standards for network messages with three byte headers*
* J2284-3 - Defines 500K CAN Physical and Data Link Layer
[edit] ISO standards
* ISO 9141: Road vehicles — Diagnostic systems. International Organization for Standardization, 1989.
o Part 1: Requirements for interchange of digital information
o Part 2: CARB requirements for interchange of digital information
o Part 3: Verification of the communication between vehicle and OBD II scan tool
* ISO 11898: Road vehicles — Controller area network (CAN). International Organization for Standardization, 2003.
o Part 1: Data link layer and physical signalling
o Part 2: High-speed medium access unit
o Part 3: Low-speed, fault-tolerant, medium-dependent interface
o Part 4: Time-triggered communication
* ISO 14230: Road vehicles — Diagnostic systems — Keyword Protocol 2000, International Organization for Standardization, 1999.
o Part 1: Physical layer
o Part 2: Data link layer
o Part 3: Application layer
o Part 4: Requirements for emission-related systems
* ISO 15765: Road vehicles — Diagnostics on Controller Area Networks (CAN). International Organization for Standardization, 2004.
o Part 1: General information
o Part 2: Network layer services
o Part 3: Implementation of unified diagnostic services (UDS on CAN)
o Part 4: Requirements for emissions-related systems
Ima li tko koji Automotive standard.
Branko
Dali ima interesenta za exchange- menjavu za koji drugi software.
Ja imam dumpove za puno auta.
Software imam ovaj:
- Air4 TMW
- Tachosoft Airbag Resetter v6.4
Nova verzija!!!
Stranice: 1